PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201)

Course Overview: PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201) Training Class is a three-day course that teaches students to configure and manage the entire line of Palo Alto Networks next-generation firewalls. This course prepares the student for the Palo Alto Networks Accredited Configuration Engineer (ACE) and progress to the Palo Alto Networks Certified Network Security Engineer (PCNSE). Through hands-on training, students learn high end skills of how to integrate Palo Alto next-generation firewalls into their network infrastructure. This is not a virtualized theoretical course. This is hands-on, real world instruction, directly relevant to the DoD and Commercial implementations of Palo Alto Networks next-generation firewalls.

Each student is issued a physical Palo Alto firewall and a Cisco layer 3 switch at their desk. Real hardware per student for real experience and real skill development. TechNow provides a very comprehensive client infrastructure that includes Windows, Linux, and multiple packet sniffer agents.

This course sets up the foundation for the two day course PA-212: Palo Alto Networks Firewall Configure Extended Features. The instructor for this course has been a lead in Unix kernel development to implement firewall and intrusion detection technologies. Additionally, the instructor has taught several security appliance products and carries several SANS, ISC2, ISACA, Cisco, Unix, and Windows certifications.

Attendees to the PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201) Training Course will receive TechNow approved course materials and expert instruction.

TechNow PA-212: Palo Alto Networks Firewall Configure Extended Features (EDU-205) immediately follows this course in the schedule so that you can take both courses in the same week. We also offer a discount for attending both classes in the same week!!

Dates/Locations: No Events

Duration: 3 days

Course Objectives: Students attending this foundational-level training course will gain an in-depth knowledge of how to configure and manage their Palo Alto Networks firewall, including hands-on experience in configuring the security, networking, threat prevention, logging, and reporting features of the Palo Alto Networks Operating System (PAN-OS).

Day 1

Module 0 – Introduction & Overview
Module 1 – Platforms and Architecture
- Single-Pass Architecture
- Flow Logic
Module 2 – Initial Configuration
- Initial Access to the System
- Configuration Management
- Licensing and Software Updates
- Account Administration
Mod 3: Basic Interface Configuration
- Security Zones
  Layer 2, Layer 3, Virtual Wire, and Tap
- Subinterfaces
- DHCP
- Virtual Routers
Mod 4: Security and NAT Policies
- Security Policy Configuration
- Policy Administration
- NAT (source and destination)

Day 2

Mod 5: Basic App-ID™
- App-ID Overview
- Application Groups and Filters
Mod 6: Basic Content-ID™
- Antivirus
- Anti-spyware
- Vulnerability
- URL Filtering
Mod 7: File Blocking and WildFire™
- File Blocking
- WildFire
Mod 8: Decryption
- Certificate Management
- Outbound SSL Decryption
- Inbound SSL Decryption

Day 3

Mod 9: Basic User-ID™
- Enumerating Users
- Mapping Users to IP Addresses
- User-ID Agent
Mod 10: Site-to-Site VPNs
- IPSec Tunnels
Mod 11: Management and Reporting
- Dashboard
- Basic Logging
- Basic Reports
- Panorama
Mod 12: Active/Passive High
- Availability
- Configuring Active/Passive HA

Prerequisites:

Security+, Network+, CCNA and networking experience is recommended.

This course is in no way associated with Palo Alto Networks, Inc.

Comments

Latest comments from students

Like the class? Then let everyone know!

TN-835: Certified in Risk and Information Systems Control (CRISC) Preparation Seminar

Course Overview:

Certified in Risk and Information Systems Control (CRISC), is for professionals responsible for an organization's risk management program. Students looking to acquire CRISC qualify themselves as IT security analyst, security engineer architect, information assurance program manager and senior IT auditor. CRISC certified professionals manage risk, design and oversee response measures, monitor systems for risk, and ensure the organization's risk management strategies are met.

The CRISC exam will primarily align with the terminology and concepts described in The Risk IT Framework, The Risk IT Practioner Guide, and COBIT 5. This will include applications in the evaluation and monitoring of IT-based risk, as well as the design and implementation of IS controls.

The CRISC exam covers four domains that are periodically updated to reflect the changing needs of the profession:

Domain 1: Risk Identification
Domain 2: Risk Assessment
Domain 3: Risk Response and Mitigation
Domain 4: Risk and Control Monitoring and Reporting

This course is designed to assist in your exam preparation for the CRISC exam.

Attendees to TN-835: Certified in Risk and Information Systems Control (CRISC) Seminar will receive TechNow approved course materials and expert instruction.

Dates/Locations:

No Events

Duration: 5 Days

Course Objectives:

Risk IT Framework—Purpose and Principles
Essentials of Risk Governance, Evaluation, and Response
Risk and Opportunity Management Using CobiT, Val IT and Risk IT
The Risk IT Framework Process Model Overview
Managing Risk in Practice—The Practitioner Guide Overview
Overview of the Risk IT Framework Process Model
The Risk IT Framework

Prerequisites:

A minimum of at least three (3) years of cumulative work experience performing the tasks of a CRISC professional across at least three (3) CRISC domains is required for certification. There are no substitutions or experience waivers.

Comments

Latest comments from students

User: tracycampbell

Instructor comments: Dave had great command of the class and the flow of information. The lessons seem relevant to the exam and the course material should assist greatly with passing. As a bonus, his breakdown of PKI helped with my current job requirements.

Facilities comments: The Home2Suites by Hilton was FANTASTIC!

Liked the class? Then let everyone know!

N-310: CCNA Extended Bootcamp

Course Overview:

TechNow’s Course ensures that you are ready to test for the CCNA Certification. This intensive ten-day program is a high end, hands-on, bootcamp using physical routers & switches in classroom. Students will learn how to install, operate, configure, and verify basic IPv4 and IPv6 networks. The course covers configuring network components such as switches, routers, and wireless LAN controllers; managing network devices; and identifying basic security threats. The course also gives you a foundation in network programmability, automation, and software-defined networking. Additionally the course stress tests the students on exam practices that insure the student a successful outcome on the 200-301 CCNA exam.

This course is available for group purchasing with a minimum of 4 students. Please call to get scheduling availability.

Attendees to N-310: CCNA Extended Bootcamp will receive TechNow approved course materials and expert instruction.

Date/Locations:

This course is available for group purchasing with a minimum of 4 students. Please call to get scheduling availability. (210) 733-1093

No Events

Duration: 10 days

Course Objectives:

- Identify the components of a computer network and describe their basic characteristics
- Understand the model of host-to-host communication
- Describe the features and functions of the Cisco Internetwork Operating Systems (IOS) software
- Describe LANs and the role of switches within LANs
- Describe Ethernet as the network access layer of TCP/IP and describe the operation of switches
- Install a switch and perform the initial configuration
- Describe the TCP/IP Internet layer, IPv4, its addressing scheme, and subnetting
- Describe the TCP/IP Transport layer and Application layer
- Explore functions of routing
- Implement basic configuration on a Cisco router
- Explain host-to-host communications across switches and routers
- Identify and resolve common switched network issues and common problems associated with IPv4 addressing
- Describe IPv6 main features and addresses, and configure and verify basic IPv6 connectivity
- Describe the operation, benefits, and limitations of static routing
- Describe, implement, and verify Virtual Local Area Networks (VLANs) and trunks
- Describe the application and configuration of inter-VLAN routing
- Explain the basics of dynamic routing protocols and describe components and terms of Open Shortest Path First (OSPF)
- Explain how Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) work
- Configure link aggregation using EtherChannel
- Describe the purpose of Layer 3 redundancy protocols
- Describe basic WAN and VPN concepts
- Describe the operation of Access Control Lists (ACLs) and their applications in the network
- Configure Internet access using Dynamic Host Configuration Protocol (DHCP) clients and explain and configure Network Address Translation (NAT) on Cisco routers
- Describe basic Quality of Service (QoS) concept
- Describe network and device architectures and introduce virtualization
- Introduce the concept of network programmability and Software-Defined Networking (SDN)
- Configure basic IOS system monitoring tools
- Describe the management of Cisco devices
- Describe the current security threat landscape
- Describe threat defense technologies
- Implement a basic security configuration of the device management plane
- Implement basic steps to harden network devices

Lab Objectives:

- - Get started with Cisco Command-Line Interface (CLI)
  - Observe How a Switch Operates
  - Perform Basic Switch Configuration
  - Implement the Initial Switch Configuration
  - Inspect TCP/IP Applications
  - Configure an Interface on a Cisco Router
  - Configure and Verify Layer 2 Discovery Protocols
  - Implement an Initial Router Configuration
  - Configure Default Gateway
  - Explore Packet Forwarding
  - Troubleshoot switch Media and Port Issues
  - Troubleshoot Port Duplex Issues
  - Configure Basic IPv6 Connectivity
  - Configure and Verify IPv4 Static Routes
  - Configure Iv6 Static Routes
  - Implement IPv4 Static Routing
  - Implement IPv6 Static Routing
  - Configure VLAN and Trunk
  - Troubleshoot VLANs and Trunk
  - Configure a Router on a Stick
  - Implement Multiple VLANs and Basic Routing Between the VLANs
  - Configure and Verify Single-Area OSPF
  - Configure and Verify EtherChannel
  - Improve Redundant Switched Topologies with EtherChannel
  - Configure and Verify IPv4 ACLs
  - Implement Numbered and Named IPv4 ACLs
  - Configure a Provider-Assigned IPv4 Address
  - Configure Static NAT
  - Configure Dynamic NAT and Port Address Translation (PAT)
  - Implement PAT
  - Log into the WLC
  - Monitor the WLC
  - Configure a Dynamic (VLAN) Interface
  - Configure a DHCP Scope
  - Configure a WLAN
  - Define a Remote Access Dial-In User Service (RADIUS) Server
  - Explore Management Options
  - Explore the Cisco DNA Center
  - Configure and Verify NTP
  - Configure System Message Logging
  - Create the Cisco IOS Image Backup
  - Upgrade Cisco IOS Image
  - Configure WLAN Using Wi-Fi Protected Access 2 (WPA2) Pre-Shared Key (PSK) Using the GUI
  - Secure Console and Remote Access
  - Enable and Limit Remote Access Connectivity
  - Secure Device Administrative Access
  - Configure and Verify Port Security
  - Implement Device Hardening

Prerequisites:

- - Familiarity in the following networking topics:
    - TCP/IP
    - IP Configuration
    - Peer-to-Peer Networking
    - Subnetting
    - Building a Routing Table
  - It is not required but highly recommended to have the following certifications:
    - Security +
    - Network +

Comments

Latest comments from students

User: kdinivahi29

Instructor comments: The instructor Mr. Tom Bigger has done a terrific job of substantiating the textbook content with hands on labs. He has been patient and ensure that we understood the material

User: MikeWisn

Instructor comments: Did exceptional job explaining complicated concepts.

Facilities comments: Hotel front desk phone ringing loudly during class was distracting.

Liked the class? Then let everyone know!

CT-395: CySA+ Cybersecurity Analyst

Course Overview:

CT-395: CompTIA CySA+ Cybersecurity Analyst is for IT professionals looking to gain IT security analyst skills, and for those following the recommended skills pathway to achieve cybersecurity mastery. It provides a bridge between CompTIA Security+ (CT-325) and CompTIA Advanced Security Practitioner (CASP,CT-425), thus completing a certification path within the CompTIA family of certifications. As attackers have learned to evade traditional signature-based solutions, an analytics-based approach has become extremely important. CySA+ applies behavioral analytics to the IT security market to improve the overall state of security. The CompTIA Cybersecurity Analyst (CySA+) certification verifies that successful candidates have the knowledge and skills required to configure and use threat detection tools, perform data analysis and interpret the results to identify vulnerabilities, threats and risks to an organization, with the end goal of securing and protecting applications and systems within an organization. Let us help you bridge this gap, and leave you prepared for the certification exam (CS0-002).

TechNow is a CompTIA partner uses official CompTIA CySA+ curriculum.

Dates/Locations:

Date/Time	Event
03/03/2025 - 03/07/2025 09:00 -17:00	CT-395: CySA+ Cybersecurity Analyst TechNow, Inc, San Antonio TX
06/02/2025 - 06/06/2025 09:00 -17:00	CT-395: CySA+ Cybersecurity Analyst TechNow, Inc, San Antonio TX
09/08/2025 - 09/12/2025 08:00 -16:00	CT-395: CySA+ Cybersecurity Analyst TechNow, Inc, San Antonio TX
12/01/2025 - 12/05/2025 08:00 -16:00	CT-395: CySA+ Cybersecurity Analyst TechNow, Inc, San Antonio TX

Duration: 5 Days

Course Objectives:

Threat Management
Vulnerability Management
Cyber Incident Response
Security Architecture and Tool Sets

Prerequisites:

While there is no required prerequisite, the CompTIA CySA+ certification is intended to follow CT-325: Security+ or equivalent experience. It is recommended for CompTIA CySA+ candidates to have the following:

3-4 years of hands-on information security or related experience
Network+, Security+, or equivalent knowledge.

Comments

Latest comments from students

Liked the class? Then let everyone know!

TN-855: Advanced and In-Depth ICD 503 RMF, Controls, and Assessments

Course Overview:

This course is very hands-on with respect to SP 800-53 controls as related to ICD-503, leveraging experience with DCD 6/3, and incorporating a broad array of technologies found in the field. Assessors and Auditors have to face many technologies that are not part of the main stream. TechNow has gone to great efforts to build a very broad, comprehensive, and complex lab to simulate many scenarios and architectures. Technologies such as a network appliance that is not a typical infrastructure product, a radio/satellite communications device, or many other technologies that build up a weapon system. Students learn how controls are integrated into many different devices and how they fit in the overall security architecture of monitoring, reporting, and compliance testing.

Directly discussed are overlays for different requirements i.e.: tactical, medical, network type: JWICS, SIPR; IC or AF. TechNow has developed a funnel concept to overlays to exemplify the encapsulation of a control within different requirements. TechNow has over 15 years experience in Trusted Solaris/Trusted Extensions and labeled security. Cross Domain overlays are presented that fits the work flow of an assesor. PII overlays and any overlays that an organization uses and can be made available are also presented.

This course allows the student to leverage years of experience in DoD DCD 6/34 for transition to the Risk Management Framework (RMF) applied to the Intelligence Community as mandated by ICD 503. Utilizing NIST SP 800-37 to establish a baseline of RMF knowledge, the student learns how to integrate the NIST pubs to provide cohesive information assurance architectures and compliance. ICD 503 scorecard evaluations are integral in demonstrating a successful ICD 503 compliance program. TechNow's ICD 503 course provides students with the skill to assess security programs and evaluate ICD 503 compliance to build an improvement and sustainable program for score consistency. TechNow's instructors have unparralleled expertise in federal compliance initiatives, and we bring this expertise instructing students on the complete life cycle of RMF.

More than a simple checklist, we instruct students not only how to validate essential security controls, programs, and metrics, but that they are operating effectively. The student leaves the course knowing how to: identify gaps where controls, programs, or metrics are incomplete, missing or ineffective, and provide actionable findings and recommend remediation strategies. Students learn to internalize NIST pubs to meaningul and effective IA guidelines and work with the Body of Evidence templates which include: Risk Assessment Report (RAR), Systems Security Plan (SSP), Security Assessment Report (SAR), and Plans of Action and Milestone (POAM).

TechNow training materials are aligned with the most recent set of National Institute of Standards and Technology (NIST), Committee on National Security Systems (CNSS), and Office of the Director of National Intelligence (ODNI) policies standards, processes, policies and instructions to be addressed/explained include ICD 503, ICS 503-1, ICS 500-16, ICS 500-18, ICS 500-27, ICD 502, NIST SP 800-37, NIST SP 800-30, NIST SP 800-53, NIST SP 800-53A, NIST SP 800-137, NIST SP 800-47, CNSSP 22, CNSSI 1253, and CNSSI 4009.

A majority of time is spent on in-depth compliance review of NIST SP 800-53 controls. Instruction discusses which method should be used to test and validate each security control and what evidence should be gathered. This course is not theory or death by power point. Real scenarios are presented as exercises. A complete live cyber range simulating the IC is utilized for hands-on labs for techniques of validating and documenting compliance of NIST SP 800-53 controls as related to ICD 503.

Date/Locations:

No Events

Duration: 5 days

Course Objectives:

Establish a baseline of RMF knowledge
Validate essential security controls, programs, and metrics
DoD DCD 6/3 to ICD 503 Transition
Lab Environtment and the Cyber Range
Overlays: Tactical, Medical, Network type(JWICS, SIPR; IC or AF), Cross Domain, PII
Risk Assessment Report (RAR)
Systems Security Plan (SSP)
Security Assessment Report (SAR)
Plans of Action and Milestone (POAM)