PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201)

Course Overview: PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201) Training Class is a three-day course that teaches students to configure and manage the entire line of Palo Alto Networks next-generation firewalls. This course prepares the student for the Palo Alto Networks Accredited Configuration Engineer (ACE) and progress to the Palo Alto Networks Certified Network Security Engineer (PCNSE). Through hands-on training, students learn high end skills of how to integrate Palo Alto next-generation firewalls into their network infrastructure. This is not a virtualized theoretical course. This is hands-on, real world instruction, directly relevant to the DoD and Commercial implementations of Palo Alto Networks next-generation firewalls.

Each student is issued a physical Palo Alto firewall and a Cisco layer 3 switch at their desk. Real hardware per student for real experience and real skill development. TechNow provides a very comprehensive client infrastructure that includes Windows, Linux, and multiple packet sniffer agents.

This course sets up the foundation for the two day course PA-212: Palo Alto Networks Firewall Configure Extended Features. The instructor for this course has been a lead in Unix kernel development to implement firewall and intrusion detection technologies. Additionally, the instructor has taught several security appliance products and carries several SANS, ISC2, ISACA, Cisco, Unix, and Windows certifications.

Attendees to the PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201) Training Course will receive TechNow approved course materials and expert instruction.

TechNow PA-212: Palo Alto Networks Firewall Configure Extended Features (EDU-205) immediately follows this course in the schedule so that you can take both courses in the same week. We also offer a discount for attending both classes in the same week!!

Dates/Locations: No Events

Duration: 3 days

Course Objectives: Students attending this foundational-level training course will gain an in-depth knowledge of how to configure and manage their Palo Alto Networks firewall, including hands-on experience in configuring the security, networking, threat prevention, logging, and reporting features of the Palo Alto Networks Operating System (PAN-OS).

Day 1

Module 0 – Introduction & Overview
Module 1 – Platforms and Architecture
- Single-Pass Architecture
- Flow Logic
Module 2 – Initial Configuration
- Initial Access to the System
- Configuration Management
- Licensing and Software Updates
- Account Administration
Mod 3: Basic Interface Configuration
- Security Zones
  Layer 2, Layer 3, Virtual Wire, and Tap
- Subinterfaces
- DHCP
- Virtual Routers
Mod 4: Security and NAT Policies
- Security Policy Configuration
- Policy Administration
- NAT (source and destination)

Day 2

Mod 5: Basic App-ID™
- App-ID Overview
- Application Groups and Filters
Mod 6: Basic Content-ID™
- Antivirus
- Anti-spyware
- Vulnerability
- URL Filtering
Mod 7: File Blocking and WildFire™
- File Blocking
- WildFire
Mod 8: Decryption
- Certificate Management
- Outbound SSL Decryption
- Inbound SSL Decryption

Day 3

Mod 9: Basic User-ID™
- Enumerating Users
- Mapping Users to IP Addresses
- User-ID Agent
Mod 10: Site-to-Site VPNs
- IPSec Tunnels
Mod 11: Management and Reporting
- Dashboard
- Basic Logging
- Basic Reports
- Panorama
Mod 12: Active/Passive High
- Availability
- Configuring Active/Passive HA

Prerequisites:

Security+, Network+, CCNA and networking experience is recommended.

This course is in no way associated with Palo Alto Networks, Inc.

Comments

Latest comments from students

Like the class? Then let everyone know!

N-310: CCNA Extended Bootcamp

Course Overview:

TechNow’s Course ensures that you are ready to test for the CCNA Certification. This intensive ten-day program is a high end, hands-on, bootcamp using physical routers & switches in classroom. Students will learn how to install, operate, configure, and verify basic IPv4 and IPv6 networks. The course covers configuring network components such as switches, routers, and wireless LAN controllers; managing network devices; and identifying basic security threats. The course also gives you a foundation in network programmability, automation, and software-defined networking. Additionally the course stress tests the students on exam practices that insure the student a successful outcome on the 200-301 CCNA exam.

This course is available for group purchasing with a minimum of 4 students. Please call to get scheduling availability.

Attendees to N-310: CCNA Extended Bootcamp will receive TechNow approved course materials and expert instruction.

Date/Locations:

This course is available for group purchasing with a minimum of 4 students. Please call to get scheduling availability. (210) 733-1093

No Events

Duration: 10 days

Course Objectives:

- Identify the components of a computer network and describe their basic characteristics
- Understand the model of host-to-host communication
- Describe the features and functions of the Cisco Internetwork Operating Systems (IOS) software
- Describe LANs and the role of switches within LANs
- Describe Ethernet as the network access layer of TCP/IP and describe the operation of switches
- Install a switch and perform the initial configuration
- Describe the TCP/IP Internet layer, IPv4, its addressing scheme, and subnetting
- Describe the TCP/IP Transport layer and Application layer
- Explore functions of routing
- Implement basic configuration on a Cisco router
- Explain host-to-host communications across switches and routers
- Identify and resolve common switched network issues and common problems associated with IPv4 addressing
- Describe IPv6 main features and addresses, and configure and verify basic IPv6 connectivity
- Describe the operation, benefits, and limitations of static routing
- Describe, implement, and verify Virtual Local Area Networks (VLANs) and trunks
- Describe the application and configuration of inter-VLAN routing
- Explain the basics of dynamic routing protocols and describe components and terms of Open Shortest Path First (OSPF)
- Explain how Spanning Tree Protocol (STP) and Rapid Spanning Tree Protocol (RSTP) work
- Configure link aggregation using EtherChannel
- Describe the purpose of Layer 3 redundancy protocols
- Describe basic WAN and VPN concepts
- Describe the operation of Access Control Lists (ACLs) and their applications in the network
- Configure Internet access using Dynamic Host Configuration Protocol (DHCP) clients and explain and configure Network Address Translation (NAT) on Cisco routers
- Describe basic Quality of Service (QoS) concept
- Describe network and device architectures and introduce virtualization
- Introduce the concept of network programmability and Software-Defined Networking (SDN)
- Configure basic IOS system monitoring tools
- Describe the management of Cisco devices
- Describe the current security threat landscape
- Describe threat defense technologies
- Implement a basic security configuration of the device management plane
- Implement basic steps to harden network devices

Lab Objectives:

- - Get started with Cisco Command-Line Interface (CLI)
  - Observe How a Switch Operates
  - Perform Basic Switch Configuration
  - Implement the Initial Switch Configuration
  - Inspect TCP/IP Applications
  - Configure an Interface on a Cisco Router
  - Configure and Verify Layer 2 Discovery Protocols
  - Implement an Initial Router Configuration
  - Configure Default Gateway
  - Explore Packet Forwarding
  - Troubleshoot switch Media and Port Issues
  - Troubleshoot Port Duplex Issues
  - Configure Basic IPv6 Connectivity
  - Configure and Verify IPv4 Static Routes
  - Configure Iv6 Static Routes
  - Implement IPv4 Static Routing
  - Implement IPv6 Static Routing
  - Configure VLAN and Trunk
  - Troubleshoot VLANs and Trunk
  - Configure a Router on a Stick
  - Implement Multiple VLANs and Basic Routing Between the VLANs
  - Configure and Verify Single-Area OSPF
  - Configure and Verify EtherChannel
  - Improve Redundant Switched Topologies with EtherChannel
  - Configure and Verify IPv4 ACLs
  - Implement Numbered and Named IPv4 ACLs
  - Configure a Provider-Assigned IPv4 Address
  - Configure Static NAT
  - Configure Dynamic NAT and Port Address Translation (PAT)
  - Implement PAT
  - Log into the WLC
  - Monitor the WLC
  - Configure a Dynamic (VLAN) Interface
  - Configure a DHCP Scope
  - Configure a WLAN
  - Define a Remote Access Dial-In User Service (RADIUS) Server
  - Explore Management Options
  - Explore the Cisco DNA Center
  - Configure and Verify NTP
  - Configure System Message Logging
  - Create the Cisco IOS Image Backup
  - Upgrade Cisco IOS Image
  - Configure WLAN Using Wi-Fi Protected Access 2 (WPA2) Pre-Shared Key (PSK) Using the GUI
  - Secure Console and Remote Access
  - Enable and Limit Remote Access Connectivity
  - Secure Device Administrative Access
  - Configure and Verify Port Security
  - Implement Device Hardening

Prerequisites:

- - Familiarity in the following networking topics:
    - TCP/IP
    - IP Configuration
    - Peer-to-Peer Networking
    - Subnetting
    - Building a Routing Table
  - It is not required but highly recommended to have the following certifications:
    - Security +
    - Network +

Comments

Latest comments from students

User: kdinivahi29

Instructor comments: The instructor Mr. Tom Bigger has done a terrific job of substantiating the textbook content with hands on labs. He has been patient and ensure that we understood the material

User: MikeWisn

Instructor comments: Did exceptional job explaining complicated concepts.

Facilities comments: Hotel front desk phone ringing loudly during class was distracting.

Liked the class? Then let everyone know!

PA-212: Palo Alto Networks Firewall Configure Extended Features (EDU-205)

Course Overview: PA-212: Palo Alto Networks Firewall Configure Extended Features (EDU-205) Training Class is a two-day course that teaches students to configure and manage the entire line of Palo Alto Networks next-generation firewalls. Students also will be instructed on the basics of implementing and managing GlobalProtect™ and active/ active high availability. Students will gain an in-depth knowledge of how to optimize their visibility and control of applications, users, and content. This course prepares the student for Palo Alto Networks Certified Network Security Engineer (PCNSE). Through hands-on training, students learn high end skills of how to integrate Palo Alto next-generation firewalls into their network infrastructure. This is not a virtualized theoretical course. This is hands-on, real world instruction, directly relevant to the DoD and Commercial implementations of Palo Alto Networks next-generation firewalls.

Each student is issued a physical Palo Alto firewall and a Cisco layer 3 switch at their desk. Real hardware per student for real experience and real skill development. TechNow provides a very comprehensive client infrastructure that includes Windows, Linux, and multiple packet sniffer agents.

This course sets up the foundation for the three day course PA-243: Palo Alto Networks Firewall Debug and Troubleshoot (EDU-311). The instructor for this course has been a lead in Unix kernel development to implement firewall and intrusion detection technologies. Additionally, the instructor has taught several security appliance products and carries several SANS, ISC2, ISACA, Cisco, Unix, and Windows certifications. Attendees to the PA-212: Palo Alto Networks Firewall Configure Extended Features (EDU-205) Training Course will receive TechNow approved course materials and expert instruction.

Dates/Locations: No Events

Duration: 2 days

Course Objectives: Students attending this foundational-level training course will gain an in-depth knowledge of how to configure and manage their Palo Alto Networks firewall. Students also will be instructed on the basics of implementing and managing GlobalProtect™ and active/ active high availability. Students will gain an in-depth knowledge of how to optimize their visibility and control of applications, users, and content.

Day 1

Module 0 – Introduction & Overview
Mod 1: Advanced Interface
- Configuration
- Advanced NAT
- Policy-Based
- Forwarding
- Routing Protocols (OSPF)
Mod 2: App-ID™ –
- Custom Applications
- Defining New Application Signatures
- Application Override
Mod 3: Advanced Content-ID™
- Custom Threat Signatures
- Data Filtering
- DoS Protection
- Botnet Report
Mod 4: Advanced User-ID™
- Terminal Server Agent
- Captive Portal
- XML API

Day 2

Mod 5: Quality of Service
- Configuring Quality of Service
Mod 6: GlobalProtect™
- Implementation of GlobalProtect
- Install and Configure Portal, Gateway, and Agents
Mod 7: Monitoring and Reporting
- Log Forwarding
- SNMP
- Reporting
Mod 8: Active/Active High Availability
- Configuring Active/Active HA

Prerequisites:

PA-213: Palo Alto Networks Firewall Install, Configure, and Manage (EDU-201)

This course is in no way associated with Palo Alto Networks, Inc.

Comments

Latest comments from students

Like the class? Then let everyone know!

TN-542: Establishing a Security Operations Center (SOC) People, Processes, and Technologies

Course Overview:

TN-542: Establishing a Security Operations Center (SOC) People, Processes, and Technologies is the big picture overview of a SOC, other courses provide a deep dive into the technologies that a SOC may utilize. This course addresses the internal workings of staff, skills required, required authorizations, internal agreements, and setting appropriate expectation levels of a SOC within budget constraints. A SOC is not a one size fits all, the instructor has decades of security experience and brings to the table opportunities to discuss what can work within constraints. Many organizations are coming to the realization that some level of a SOC is now required and to learn just what decisions need to be made: Out-sourced, In-sourced, budgets, capabilities and many more. Students leave with a worksheet of how to progress when they get back to their organization.

TN-542: Establishing a Security Operations Center (SOC) People, Processes, and Technologies – Is a course that incorporates lecture, demos, and group exercises for standing up a Security Operations Center (SOC). Students learn strategies and resources required to deploy, build, and run Network Security Monitoring (NSM) and work roles and flows for a SOC. No network is bullet proof and when attackers access your network, this course will show you options and resources to build a security net to detect, contain, and control the attacker. Examples on what it takes to architect an NSM solution to identify sophisticated attackers and a response strategy. Properly implemented detection and response technologies is integral to incident response and provides the responders timely information and tools to react to the incident. Effective demonstrations are given of Open Source technologies that build up a SOC, but any software can be used and demonstrations are provided to demonstrate technology families not push a specific solution.

TN-542: Establishing a Security Operations Center (SOC) People, Processes, and Technologies demonstrations utilize a cyber range that gives each student in-depth knowledge of monitoring live systems to include: Cisco, Windows, Linux, IoT, and Firewalls; and software and services to provide orchestrate Incident Response, Intelligence Analysis, and Hunt Operations.

Attendees to TN-542: Establishing a Security Operations Center (SOC) People, Processes, and Technologies class will receive TechNow approved course materials and expert instruction.

Dates/Locations:

No Events

Duration: 2 Days

Course Objective:

Prerequisites:

Students should have an understanding of the security field.

Course Outline:

What threats does my organization care about?
What does a threat look like?
What does a threat look like?
How to present the SOC internally.
Communication with Stakeholders and Executives
People
- Establishing a skill matrix and work roles for SOC members
- Establishing a training path
- Personnel background requirementsProcesses
Processes
- Alignment to standards: NIST, PCI, HIPAA, etc.
- Risk related decision trees
- Playbooks
- Threat Intelligence Integration
Technology – Tool Suites to Support:
- Ethical Hacking
- Network Security Monitoring and SIEM
- Forensics
- Dashboards
- Analysis and Hunting
- Incident Management and Ticketing

Comments

Latest comments from students

Liked the class? Then let everyone know!

Unix/Linux

Over twenty years experience in the area of Solaris, Linux, and Unix ensures that you are benefiting from a very mature and successful Solaris, Linux, and Unix training program. TechNow offers the full suite of Solaris, Linux, and Unix courses utilizing real hardware. This is not virtualized Solaris on Intel processors, or remote connection to a distant system. The student learns to deal with real hardware taking advantage of Sparc T series processors. Solaris 10 and Solaris 11 is taught hands-on with data center skills as the focus. We also offer Solaris 10 migration courses to Solaris 10 or Solaris 11.

The following is a list of our Unix/Linux training courses: